Quick Start • DWC2440

DWC2440 CNC — Getting Started

This page covers the first setup steps for your DWC2440: Assembly & Setup, OmniControl (PlanetCNC TNG) installation, and Vectric CAD/CAM installation. Follow the steps in order for the smoothest first start.

Install OmniControl Install Vectric Need Help?

Assembly & Setup OmniControl Install Firmware & License Limits Setting Vectric Install Support

Assembly & Setup

Choose your DWC2440 configuration

The DWC2440 is available in three configurations. Use the section that matches what you purchased.

Benchtop Unit (No Stand)

Place the machine on a stable surface and verify it is level.
Ensure the machine is positioned and secured before continuing.

3-Axis PRO (Includes Stand)

Assemble the stand using the official assembly video.
Confirm the machine is level and secure before continuing.

Watch DWC2440 Stand Assembly Video

4-Axis PRO 3D (Stand + Rotary Axis)

Complete the stand assembly first (same as 3-Axis PRO).
Then install and set up the Rotary Axis using the rotary video.

Stand Assembly Video Rotary Axis Install & Setup Video

What’s Included (DWC2440): Use this checklist to confirm your shipment.

(1) DWC2440 CNC unit
(2) Dust skirts
(2) Wood clamps
(1) 60° V-Bit
(1) Flash drive with software setup files
(1) 6-foot USB Cable
(2) Wrenches for changing tools
(1) 1/4 Collet & Nut
(1) 1/2 Collet & Nut

Optional add-ons: Any additional accessories you purchased may be included and will vary by order.

Step 1 — Install OmniControl (PlanetCNC TNG)

Software that runs the CNC

USB Flash Drive Contents (Standard):

Files

Vectric Registration and License Info.txt
PlanetCNC License Key Code.txt

Folders

DWC SetUp & Information (Vectric setup files & more)
2440 complete (OmniControl Profile)
PlanetCNCWin_<Latest_Release> (PlanetCNC installer)

If your USB contents do not match, use the official download links below.

Insert the USB Flash Drive into your PC.
Verify its contents match the USB Flash Drive Contents listed above.
If the contents do not match, click here to download the DWC2440 setup files .
If the PlanetCNCWin_<Latest_Release> folder is missing, download PlanetCNC from planet-cnc.com/download.html.
Open the PlanetCNCWin_<Latest_Release> folder and run PlanetCNC_Installer.exe.
If Windows blocks it, click More Info → Run Anyway.
During install, uncheck auto-open (do not launch immediately after install).
For the next steps, it helps to have two File Explorer windows open side-by-side.
In one window, open the 2440 complete folder. In the other, open C:\Program Files\PlanetCNC.
From 2440 complete, copy the Profiles folder into C:\Program Files\PlanetCNC.
In the C:\Program Files\PlanetCNC window, navigate to your Desktop folder.
From 2440 complete, copy the 2440_OmniControl shortcut to your Desktop.
Close both File Explorer windows.
On your Desktop, right-click 2440_OmniControl → Properties → General tab → check Unblock (if prompted).
Click Apply, then OK.
At the CNC, connect the USB cable with the machine OFF.
Double-click the 2440_OmniControl shortcut to open OmniControl.
In OmniControl: File → Settings → Connection → double-click your USB PlanetCNC board/serial option.

Safety: Keep the machine OFF until firmware + license steps are complete.

If you’re not at the machine yet: You can install PlanetCNC and copy profiles/shortcut now. Complete steps 15–17 when you are at the CNC with the USB cable connected.

Firmware & License

Finish setup and confirm the green status light

Firmware Update

Go to Machine → Controller → Firmware Update.
Run the update and wait for success.

Activate License

Go to Help → License Management → Licenses.
Import the key code from your USB license file.
Ready state: bottom-right status light is solid green.

Goal: Solid green status light = all systems go.

Limits Setting (If No Limit Switch Kit)

DWC1824 / DWC2440 note

Limit switches are not included with this unit: go to File → Settings → Limits.
Verify the Pos/Neg limits are unchecked (no check marks).

Later upgrade: Limit switch kits are available through BuildItTV LLC as a 3rd party accessory. If you install the limit switch kit in the future, you’ll turn Limits on.

Step 2 — Install Vectric CAD/CAM

Design & toolpath software

On your USB Flash Drive, locate Vectric Registration and License Info.txt.
Copy the Registration URL and paste it into your browser.
Complete the registration form and click Submit.
Check your email for an automated response from Vectric Ltd.
Click the link in the email to finish account setup and create a password.
Log in to your Vectric V&Co account dashboard.
Click Your Software → then click the Click for Details button.
Download the Vectric installer.
Run the installer → follow prompts.
At the end of install, use the Machine Setup prompt to download your Machine Post Processor and Tool Database files.
Launch VCarve or Aspire when finished.

Video: The updated Vectric install video will be linked here once the new version is published.

Need Help?

We’ve got you

If you run into any issues during setup or installation, contact support and we’ll help you get up and running.

Support Page Digital Wood Carver YouTube Schedule Your Orientation Training Session